INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, FINISH-CURE™ should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on FINISH-CURE™. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. FINISH-CURE™ is best mixed in a disposable cup.
Super-Gold+ Gap Filling CA Glue 2oz
This is the Micro-Mesh Model Polishing Kit from Revell. cnh 11/30/09 ir/jxs
The SC Rear for the Volition replaces the stock bumper but still uses the stock bumper brace as support.
Red Baron Odor Free CA’s are completely odorless, foam safe cyanoacrylates, but will bond any material that our regular line of Red Baron CA products will. Because it is different chemically, many people who are allergic to regular CA’s can often use Red Baron Odor Free CA’s without problems. Unlike many other odorless CAs in the market place today, there is very little compromise in bonding strength or curing times. They have practically the same bonding strengths (almost two tons in tensile strength) and curing times as our regular CA products.
The X-ACTO Needle File Set is the ideal tool for shaping, smoothing and applying the finishing touches to any of your unique craft projects. Our set features a quick change handle and the following files:Round file Knife file Equaling file Square file Half round file This needle file set is great for working with woods, plastics and most metals. X-ACTO blades are designed to allow you to make the careful and detailed cuts you need time and time again. Our blades are created with care and exceptional craftsmanship, producing a cutting edge that stays sharp over a longer period of time. An X-ACTO quality blade is always ready when you need it.
Odorless, equal-mix, Cures in 6 to 8 hours. Easy sanding. Great for glass cloth, sheeting wings. Compatible with many polyester resins.
Quality alloy steel.
Includes ten different double ended riffler files.
Perfect for intricate work.
Needle Files can be used to work plastic, resin, white metal, pewter, diecast Zamak, brass and other soft metals, and wood. Needle files are durable and can be used in all phases of kit assembly, like enlarging openings, shaping and fitting parts, eliminating seams and more.
SUPER-GOLD™ is odorless INSTA-CURE CAs. It is non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic.
SUPER-GOLD™cures to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.
QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour.
MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.
Attention:Because of shipping restrictions this product cannot be sold to Canada.
Paint Polishing Soft Touch Pads (5 diff grits/Bag)
The Easy-Touch Hand Sander is the ideal sanding tool for home and hobby use.
Superfine White 2-Part Self Hardening Putty
Hobby Stix Sanding Sticks (7 diff grits/Bag)
A sprayable, synthetic elastomer based adhesive. Fast tacking; ideal for low pressure spraying with minimal misting and cobwebbing. Offers high coverage and long bonding range. Low soak-in for for long lasting bond. High tack, high coverage and fast drying for permanently attaching foils, carpeting, paper, cardboard, felt, and cloth to painted or unpainted metals, wood and hardboard (not recommended for use on foam, vinyl materials or automotive headliners). Can be used for a variety of jobs in display and furniture, attaching insulation to sheet metal, attaching wiring diagrams and labels, bonding gaskets in water pumps, and bonding thin decorative film, foils, and fabric. Resists bleeding, staining, or wrinkling. Bonds quickly in 15 seconds. Nearly clear color when dry.
Quality alloy steel.
Includes nine different shapes plus an extra rat tail file.
Perfect for plastic, brass, white metal parts, etc.
Pacer ZIP KICKER Super-Glue accelerator is the best working accelerator for ZAP and other super glues you'll ever find! A little spritz works in seconds.
The Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's extender tip #304 works on the Pocket CA and all our other tops.
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.